At 7 MHz, a wire dipole needs roughly 67 feet from end to end; at 14 MHz, it needs about 33 feet. Double the frequency and the estimated length falls by half. A calculation of antenna length begins with the frequency you want to receive or transmit, not with the space available in the yard.
A calculator for a dipole antenna turns that frequency into a practical wire length. The answer describes both arms together, with the feed point in the middle. If you cut each arm to the full result, the completed antenna will be twice the intended size.
Dipole antenna calculator: the practical formula
For a half-wave antenna length calculation using a simple center-fed wire dipole, use:
Total length in feet = 468 ÷ frequency in megahertz (MHz)
For a dipole calculation, divide that result by two for each arm, or use 234 ÷ frequency in MHz directly. An antenna length calculator based on this rule estimates the active wire from one end to the other. A dipole antenna calculator can make the same division for you. Allow extra wire for attaching the ends and making connections; that allowance is separate from the estimated active length.
The ARRL’s single-band dipole guide uses this same formula and recommends leaving extra wire for adjustment. It is an estimate for a straightforward wire dipole, not a measurement of the finished antenna’s response. Wire diameter, insulation, height, nearby objects and the final shape can shift the frequency at which it works best.
Why frequency determines length
Radio waves travel through free space at approximately 186,000 miles per second. Wavelength is the distance a wave travels during one cycle. Higher frequency means shorter wavelength.
For frequency in MHz, free-space wavelength is approximately 984 ÷ frequency in feet. Half of that is 492 ÷ frequency. The practical dipole calculation uses 468 instead of 492, giving an initial length about 5% shorter than a half wavelength in free space. The physical conductor and its surroundings affect its electrical behavior; the 5% adjustment is a convenient rule, not a correction that fits every installation.
A calculation tool should therefore tell you which formula it uses. A result based on 492 is a free-space half wavelength; the 468 result is the usual practical estimate for a wire dipole.
Worked example: 14.2 MHz
Suppose you want a dipole centered near 14.2 MHz. Keep frequency in MHz and proceed in this order:
- Divide 468 by 14.2: the estimated total active length is 32.96 feet.
- Divide by two: each arm is 16.48 feet.
- Convert the fractional foot to inches: 0.48 × 12 is about 5.6 inches. Each arm is approximately 16 feet 5.7 inches.
- Leave extra wire at the ends for adjustment and fastening, then measure the active portion again after assembly.
The total from this dipole sizing calculation is about 32 feet 11.5 inches. Measure each arm from the center feed connection to its outer end; the two arms should be approximately equal. Keep both results with your calculation of antenna size.
If your frequency is given in kilohertz, divide by 1,000 first: 14,200 kHz is 14.2 MHz. Entering 14,200 directly into a formula expecting MHz produces a result 1,000 times too short. If a tool returns meters, multiply by approximately 3.281 to get feet, then multiply any fractional foot by 12 to get inches.
Measure and tune the installed wire
This antenna-length estimate gets the wire in the neighborhood. The installed antenna refines your calculation of antenna length. Put it at its intended height and orientation before measuring: moving it afterward can change its response. Keep the wire clear of power lines, and disconnect transmitting equipment before handling it.
An antenna analyzer can show how impedance changes across frequency. A standing wave ratio (SWR) meter indicates how well the antenna system matches the feed line at a tested frequency. Sweep or measure across the intended range and note where SWR is lowest. That minimum is a practical tuning indicator, although lowest SWR alone does not prove resonance or tell you how efficiently the antenna radiates.
If the minimum falls below your target frequency, the antenna is generally electrically too long. Shorten both arms by small equal amounts, reconnect and measure again. Fold the ends back temporarily if practical, so you can reverse an adjustment. If the minimum is above the target, more length may be needed; add equal wire to both sides and retest. Record the change and new reading each time.
Choose the right model
A 1/2 wave antenna calculator for a center-fed wire dipole does not describe every antenna sold as a half-wave design. A folded dipole, for example, has a different conductor arrangement and feed-point impedance. A quarter-wave vertical uses a vertical element and a ground system; a loaded antenna uses components that change its electrical length. Follow the design’s own dimensions and matching instructions for those cases.
A sizing tool can suggest dimensions, but it cannot see the roof, trees or feed-line connections. For reception, compare signal quality after adjustment. For transmitting, check the match across the frequencies you intend to use and stay within your equipment’s limits.
The most likely measurement mistake is treating the total length as the length of each arm. If both sides measure roughly the full figure from a dipole antenna calculation, the wire is about twice as long as planned and its response will fall much lower in frequency. Recheck the MHz entry, divide the total by two, adjust both arms equally, and measure the installed antenna again.



